DIN EN 1007-5-2003 高级工业陶瓷.陶瓷复合材料.增强纤维的试验方法.第5部分:室温下复丝束中长丝断开时的拉伸强度和拉伸应变分布的测定

作者:标准资料网时间:2024-05-02 01:16:55 浏览:8534 来源:标准资料网

【英文标准名称】:Advancedtechnicalceramics-Ceramiccomposites;Methodsoftestforreinforcements-Part5:Determinationofdistributionoftensilestrengthandoftensilestraintofailureoffilamentswithinamultifilamenttowatambienttemperature;Germanversion
【原文标准名称】:高级工业陶瓷.陶瓷复合材料.增强纤维的试验方法.第5部分:室温下复丝束中长丝断开时的拉伸强度和拉伸应变分布的测定
【标准号】:DINEN1007-5-2003
【标准状态】:作废
【国别】:德国
【发布日期】:2003-10
【实施或试行日期】:
【发布单位】:德国标准化学会(DE-DIN)
【起草单位】:
【标准类型】:()
【标准水平】:()
【中文主题词】:试验;机械性能;加筋;材料试验;环境试验;抗断裂强度;抗拉强度;高级工业陶瓷;抗拉应力;纤维;陶瓷;增强材料;环境温度;复合材料;延伸
【英文主题词】:Advancedtechnicalceramics;Ambienttemperature;Ambienttemperatures;Breakingstrength;Ceramics;Compositematerials;Elongation;Environmentaltesting;Fibres;Materialstesting;Mechanicalproperties;Reinforcement;Reinforcingmaterial;Tensilestrength;Tensilestress;Testing
【摘要】:Thedocumentspecifiestheconditionsforthedeterminationofthedistributionofstrengthandrupturestrainofceramicfilamentswithinamultifilamenttowatroomtemperaturebyperformingasingletensiletestonamultifilamenttow.Itappliestotowsofcontinuousceramicfilamentswhichareassumedtoactfreelyandidependentlyunderloading,andbehavelinearlyelasticuptofailure.#,,#
【中国标准分类号】:Q32
【国际标准分类号】:81_060_30
【页数】:21P.;A4
【正文语种】:德语

下载地址: 点击此处下载

返回跳至顶部

上一篇: BS EN 13042-5-2003+A1-2009 中空玻璃生产、处理和加工用机械和设备.安全要求.压力机
下一篇: ISO 15747-2003 静脉注射用塑料容器

【英文标准名称】:StandardTestMethodforResistanceofProtectiveClothingMaterialstoPermeationbyLiquidsorGasesUnderConditionsofContinuousContact
【原文标准名称】:连续接触条件下防护服材料耐液体或气体渗透的试验方法
【标准号】:ASTMF739-1999
【标准状态】:作废
【国别】:美国
【发布日期】:1999
【实施或试行日期】:
【发布单位】:美国材料与试验协会(ASTM)
【起草单位】:ASTM
【标准类型】:()
【标准水平】:()
【中文主题词】:渗透;气体;试验;液体;耐力;防护服装;最终制品;保健
【英文主题词】:healthprotection;gases;liquids;enduseproducts;resistance;protectiveclothing;permeation;testing
【摘要】:
【中国标准分类号】:C73
【国际标准分类号】:13_340_10
【页数】:
【正文语种】:英语

Product Code:SAE J2547
Title:Alternate Construction Nonmetallic Air Brake System Tubing
Issuing Committee:Air Brake Tubing And Tube Ftg Committee
Scope: This SAE Standard covers the minimum requirements for nonmetallic tubing as manufactured for use in air brake systems. Non-reinforced products are designated type A and reinforced products, type B. It is not intended to cover tubing for any portion of the system which operates below 驴40 掳C, above +93 掳C, above a maximum working gage pressure of 1.0 MPa, or in an area subject to attack by battery acid. This tubing is intended for use in the brake system for connections, which maintain a basically fixed relationship between components during vehicle operation. Coiled tube assemblies required for those installations where flexing occurs are covered by this document, SAE J1131, and SAE J2494-3 to the extent of setting minimum requirements on the essentially straight tube and tube fitting connections which are used in the construction of such assemblies .
Rationale: This SAE Standard covers the minimum requirements for nonmetallic tubing as manufactured for use in air brake systems. Non-reinforced products are designated type A and reinforced products, type B. It is not intended to cover tubing for any portion of the system which operates below 驴40 掳C, above +93 掳C, above a maximum working gage pressure of 1.0 MPa, or in an area subject to attack by battery acid. This tubing is intended for use in the brake system for connections, which maintain a basically fixed relationship between components during vehicle operation. Coiled tube assemblies required for those installations where flexing occurs are covered by this document, SAE J1131, and SAE J2494-3 to the extent of setting minimum requirements on the essentially straight tube and tube fitting connections which are used in the construction of such assemblies .